[isf-wifidog] Redirect question

Jeu 10 Mar 10:25:47 EST 2005

Weird... Unless you didn't "refresh" your configuration to fit with the
new 1.1.0_beta3 release, there's no reason why 1.0.2 would work but not
1.1.0_beta3. By refreshing I mean to just use the new config file and
adapt your parameters into it.

The new 1.1.0 series has a new configuration syntax at the bottom for
firewall rules and such.

Now...

Logging out is achived by disconnecting from the access point. After a
configurable timeout value, hadn't seen any traffic since a while
WiFiDog will log you out.

We could allow people to log out themselves, but usually people are gone
surfing and no wifidog window left for them to click "logout" that would
communicate their desire to wifidog. Therefore, wifidog watches and if
there's no outgoing traffic from that IP + MAC since a little while, it
logs them out.

On Thu, Mar 10, 2005 at 05:09:43PM +0200, Marios Moutzouris wrote:
> As I replied with the 1.0.2 it works though I don?t know how to do the
> logout procedure.
> 
> I tried the below settings, works fine( i go to ilesansfil auth page). So
> either the Hostname doesn?t accept IP addresses or it only works with SSL.
> 
> Marios
> 
> > -----Original Message-----
> > From: wifidog-bounces at listes.ilesansfil.org [mailto:wifidog-
> > bounces at listes.ilesansfil.org] On Behalf Of Philippe April
> > Sent: Thursday, March 10, 2005 3:50 PM
> > To: WiFiDog Captive Portal
> > Subject: Re: [isf-wifidog] Redirect question
> > 
> > Did you run "firstboot" in failsafe to wipe what you had on your
> > partition?
> > 
> > I would like to know more details. Make sure the interfaces in the
> > config are right, and then run:
> > 
> > insmod ipt_mac
> > wifidog -f -d 9
> > 
> > and forward us the details. If you have that image and that ipkg,
> > there's no reason why it wouldn't work.
> > 
> > If you want, point to our authentication server
> > 
> > AuthServer {
> >     Hostname auth.ilesansfil.org
> >     SSLAvailable yes
> >     Path /
> > }
> > 
> > That way we'll know if that's causing problem on your end.
> > 
> > On Thu, Mar 10, 2005 at 02:00:47PM +0200, Marios Moutzouris wrote:
> > > I installed the bin file. And ran the beta3. No luck.
> > >
> > > Marios
> > >
> > > > -----Original Message-----
> > > > From: wifidog-bounces at listes.ilesansfil.org [mailto:wifidog-
> > > > bounces at listes.ilesansfil.org] On Behalf Of Philippe April
> > > > Sent: Wednesday, March 09, 2005 8:57 PM
> > > > To: WiFiDog Captive Portal
> > > > Subject: Re: [isf-wifidog] Redirect question
> > > >
> > > > Yeah but if our binaries don't fit (not same versions of iptables,
> > etc.)
> > > > it won't work well.
> > > >
> > > > If you want an image for your GS that fits with our packages:
> > > >
> > > > http://www.philippeapril.com/openwrt/openwrt-gs-code.bin
> > > >
> > > > Then try the wifidog ipkgs (beta3!)
> > > >
> > > > On Wed, Mar 09, 2005 at 09:06:25AM -0800, Joe Bowser wrote:
> > > > > On Wed, 2005-03-09 at 09:47 -0500, Philippe April wrote:
> > > > > > Hmmm. Doesn't say much :)
> > > > > >
> > > > > > Is it a recent aquisition or have you had it for a little while?
> > > > > >
> > > > > > On Wed, Mar 09, 2005 at 03:41:39PM +0200, Marios Moutzouris wrote:
> > > > > > > Thanks.
> > > > > > >
> > > > > > > It says "Model No WRT54GS"
> > > > > > >
> > > > >
> > > > > This is clearly a 1.0 unit.  All original 1.0 units do not have a
> > > > > version number.  Basically, if you're using a GS, you should
> > probably
> > > > > make sure that you have the proper firmware corresponding to
> > WiFiDog.
> > > > >
> > > > > <shameless plug>
> > > > > I recommend going to http://www.infil00p.org/openwrt/snapshots/ and
> > > > > getting the relevant files to your version of the router (in your
> > case,
> > > > > pick the v2.0 directory, since that contains the G, GS and TRX files
> > for
> > > > > an OpenWRT distro, and the corresponding WiFiDog ipk.
> > > > >
> > > > > There's also a v2.2 directory for v2.2 hardware, which may or may
> > not
> > > > > work with the WRT54GS v1.1 but I have yet to pick one up to test it
> > > > > yet.
> > > > > </shameless plug>
> > > > >
> > > > > There's also other files there of interest, namely just the patches
> > that
> > > > > I already posted here, and on the OpenWRT forums. :)
> > > > >
> > > > > --
> > > > > Joe Bowser
> > > > > e-mail: bowserj at unbc dot ca
> > > > > website: http://www.infil00p.org/
> > > > >
> > > >
> > > > > _______________________________________________
> > > > > WiFiDog mailing list
> > > > > WiFiDog at listes.ilesansfil.org
> > > > > http://listes.ilesansfil.org/cgi-bin/mailman/listinfo/wifidog
> > > >
> > > > --
> > > > Philippe April
> > > > GnuPG: http://key.philippeapril.com/
> > > > Skype ID: mousetrap
> > >
> > 
> > > _______________________________________________
> > > WiFiDog mailing list
> > > WiFiDog at listes.ilesansfil.org
> > > http://listes.ilesansfil.org/cgi-bin/mailman/listinfo/wifidog
> > 
> > --
> > Philippe April
> > GnuPG: http://key.philippeapril.com/
> > Skype ID: mousetrap
> > 
> > --
> > Internal Virus Database is out-of-date.
> > Checked by AVG Anti-Virus.
> > Version: 7.0.308 / Virus Database: 266.5.7 - Release Date: 1/3/2005
> > 
> > 
> 
> -- 
> Internal Virus Database is out-of-date.
> Checked by AVG Anti-Virus.
> Version: 7.0.308 / Virus Database: 266.5.7 - Release Date: 1/3/2005
>  
> 

> _______________________________________________
> WiFiDog mailing list
> WiFiDog at listes.ilesansfil.org
> http://listes.ilesansfil.org/cgi-bin/mailman/listinfo/wifidog

-- 
Philippe April
GnuPG: http://key.philippeapril.com/
Skype ID: mousetrap